My Pages

Monday, 12 October 2026

๐ŸŽ„ Heart of Christmas — Week 6

 


A group of creative friends from the Art with Heart team are back with our Annual Heart of Christmas blog hop. Follow through the blogs each Monday night until the end of November for Christmas card inspiration.

For this week’s Christmas card, I’ve created a slider card — such a fun interactive design for the festive season. The adorable Wombat from Joyful Friends pops out of a Santa hat as you pull the SDSP on the right‑hand side. Both images are fussy‑cut, and the Santa hat comes from the Santa’s Hat stamp set. It’s honestly so cute when the Wombat peeks out.

The Christmas tree is from one of my favourite bundles, Welcome Noel. I stamped it on Peaceful Pine cardstock using the same ink colour for that tone‑on‑tone look I love. I added Christmas Epoxy Shapes to decorate the tree and tucked a few sweet little presents underneath.

The SDSP is from Neutral Noel, and the greeting is stamped on Basic White in Real Red ink. The banner is cut using the Holly Jolly Branches dies. I finished the slider card with a bow in Mossy Meadow from the Neutral Jute Combo Pack — it just felt like it needed that little something when you pull the SDSP so the Wombat pops out.

The Santa hat is stamped in Real Red, and I added Wink of Stella for sparkle.

For the Wombat, I used a mix of blends: Pecan Pie, Crumb Cake, 500, 600, and Real Red for the candy cane and hat. I added Wink of Stella on the white parts for extra shimmer.

✂️ Measurements

  • Basic White Thick: 210mm x 148mm, scored at 105mm

  • Neutral Noel SDSP (top): 132mm x 55mm

  • Neutral Noel SDSP (bottom): 132mm x 65mm

  • Real Red layer: 142mm x 99mm

  • Scraps: Basic White for Santa hat, Wombat, and sentiment; Peaceful Pine for the tree

  • Neutral Jute: 250mm

  • Slider mechanism: 10mm x 85mm (I cut 2 of these, one is at the top of the SDSP to give it some strength, I didn't need to do the V for the top one as nothing is popping out)

    • Score at: 25mm, 37.5mm, 62.5mm, 75mm

    • On the top left side, create a V

    • On the 25mm mark, measure 12.5mm

    • On the score line, mark 12.5mm from each point

    • Score from each 12.5mm mark to the side measurement

    • Add clear acetate to hold the Wombat — this is glued onto the V‑shape on the left side

I’ll post a diagram of this mechanism tomorrow to make it easier to visualise.


I hope this Slider Card inspires you.   

Happy stamping, Hx ๐Ÿงก



➡️ Next in our Hop

Next up we are visiting Claire Daly to see what she has made this week.
You can click the link above or use the next‑blog graphic below.
If you get lost at any me, head to Sharon Davern ’s blog where you will find a full list of this week’s participants. 

4 comments:

  1. Helen, this is such a cute slider card design with the little wombat sliding from behind the Santa hat!

    ReplyDelete
    Replies
    1. Thank you Kate and for taking the time to leave such a lovely comment. I genuinely appreciate your support and am delighted that you liked my Wombat popping out of the Santa hat. ๐Ÿงก

      Delete
  2. Oh how cute is your slider card with the wombat peeping out. I love it!

    ReplyDelete
  3. Ooh I just love your cute slider card and how the Wombat jumps out of the hat. Love it!

    ReplyDelete

Thank you for leaving a positive comment. Happy Stamping Helen